DCCTools Knowledgebase KB (ECU Reprogramming (Flash))

VEHICLE: 2007 – 2009 VB Sprinter 3.0L Diesel CR4 ERROR MESSAGE: Negative response 0x22 received from Write Data by Identifier request This ECU has a high flash reprogramming failure rate with...

ISSUE: Flashing a Sprinter ECM may result in an error message of “NR 0x33 for $10 $85 request, when Retry attempt has been made”. ROOT CAUSE: This flash process failure behavior is due to an ECU issue and should not be...

VEHICLE: 2006 D1/DH 2500/3500 RAM 5.9L Cummins Diesel ECUs: Omron WCM (Wireless Control Module) Cummins ECM (Engine Control Module) CM849 ISSUE: After flashing (reprogramming) a...

VEHICLES: 2007-2009 Ram 2500/3500 6.7L Cummins ECU: CM2100 Cummins ECU ISSUE: A Cummins ECM may give a false successful flash message after a flash failure or if a flash session...

VEHICLE: 2010-2012 Ram 2500/3500/4500/5500 6.7L Cummins ECU: CM2200 Cummins ECM ERROR MESSAGE: Negative response 0x71, "Transfer Suspended' received from Transfer Data request ...

DESCRIPTION: Flashing a CM2100/Aisin PCM/TCM may result in the error message, “No response received from Start Diagnostic Session Extended request”. Flashing a CM2100/Aisin PCM/TCM is very robust and has a very low...

VEHICLE: 2006 KJ 2.8L Diesel ECU: Bocsh EDC16 ECM DESCRIPTION: There is a known issue using the WiPOD VCI as the pass-through device when flashing a 2006 KJ 2.8L ECM. ...

VEHICLES: 2011-2012 JC (Journey) 2.0L Diesel 2011-2012 JF (Freemont) 2.0L Diesel ECU: Bosch EDC17 Diesel PCM (Electronic Control Module) ERROR MESSAGE: Flash process...

VEHICLES: 2009 HB (Durango) 2009 HG (Aspen) ECU: HCP (Hybrid Control Processor) ERROR MESSAGE: Negative response 0x22 - 'Conditions Not Correct' received from Start...

OVERVIEW: Beginning with the 2011 model year, the Magneti Marelli HFM is available on Chrysler PowerNet vehicles, the Dodge Journey (JC), Dodge Charger (LD), and Chrysler 300 (LX). These USB cables are to be used...

OVERVIEW: The Magneti Marelli HFM flash process does not follow the standard wiTECH flash process and requires an application developed by the ECU supplier. To flash the HFM, you must use the wiTECH Cables from the HFM USB Cable Set...

VEHICLE: 2011 JC Journey 2011 JF Journey (fiat) 2011 LD Charger 2011 LX 300 SUBJECT: When flashing the HFM ECU, USB cables must be connected to PC running the wiTECH...

VEHICLES: 2011 PM Caliber 2011 WD Durango 2011 JK Wrangler 2011 LC Challenger 2011 JS Avenger/200 2011 MK Compass/Patriot 2011 WK/W2 Grand Cherokee 2011 DS/DJ/D2/DD/DP/DX Ram Truck 2011 RT Grand...

VEHICLE: 2012 JC (Journey) Rest of World (ROW) destination ECU: Telematics Gateway Radio (TGW) DESCRIPTION: Flashing a TGW ROW Radio...

VEHICLES: 2008 JC Journey 2008 JK Wrangler 2008 KA Nitro 2008 KK Liberty ERROR MESSAGE(S): "no response received from Start Diagnostic Session Programming request" ...

DESCRIPTION: Flashing a HVAC ECU may result in an error message of “No Response to Transfer Data Request “ OR “NR 0x31 - 'Request Of Out Range' received from Request Download request”. Flashing a HVAC ECU is very robust and has...

VEHICLE: 2009-2010 DS, DJ, D2, DD, DP (Ram Trucks) ERROR MESSAGE: Negative Response 0x71 - 'Transfer Data Suspended' received from Start Diagnostic Session Programming request. DESCRIPTION: ...

VEHICLE: 2010 RT (All Engines) ECU: Cabin Compartment Node (CCN) DESCRIPTION: The 2010 RT is unique in that there are multiple vehicle devices and options that draw current from...

VEHICLE: 2011 JK (Wrangler) ECU: CCN (Cabin Compartment Node) ERROR MESSAGE: Flash process failed – no response received from Transfer Data request. DESCRIPTION: When attempting to flash reprogram...

DESCRIPTION: The Blind Spot System is composed of a blind spot module (BSM), left rear blind spot sensor, and right rear blind spot sensor. When flashing the BSM, the system must be working as designed with no diagnostic trouble...

Sprinter ECM (Engine Control Module) flash reprogramming failure

Sprinter ECM Flash (Reprogramming) Failure with “NR 0x33 for $10 $85 request, when Retry attempt has been made”

When Flashing (Reprogramming) a 2006 DR (RAM 2500/3500) 5.9L Cummins CM849 Engine Control Module (ECM), the Wireless Control Module (WCM) Becomes Unresponsive

U1601 Electronic Control Unit (ECU) Application Software Code 1 Missing OR Corrupted After Flashing (Reprogramming) Cummins Engine Control Module (ECM)

2010-2011 Cummins 6.7L ECM (Engine Control Module) Flash (Reprogramming) Failure: Negative Response 0x71, "Transfer Suspended" Received from Transfer Data Request

CM2100/Aisin PCM/TCM Flash (Reprogramming) Failure: “No Response received from Start Diagnostic Session Extended request”

2006 KJ (Liberty) 2.8L Diesel ECM (Engine Control Module) Reprogramming Error: "STAT: 10"

2011 JC/JF (Journey/Freemont) Diesel PCM (Powertrain Control Module) Flash Process Failed: No Response Received from Start Routine By Identifier request.

2009 HB/HG (Durango/Aspen) HCP (Hybrid Control Processor) Flash Reprogramming Failure: Negative Response 0x22 - "Conditions Not Correct" Received from Start Diagnostic Session Programming Request

Magneti Marelli Hands-Free Module (HFM) wiTECH USB Cable Information

2011 JC/JF/LD/LX Magneti Marelli HFM Flash Reprogramming Procedure (with Videos)

2011 JC/JF/LD/LX (Journey/Charger/300C) Hands-Free Module (HFM) ECU: Windows XP Prompts for a Restart to Finish USB Driver Install

2011 PM/WD/JK/LC/JS/MK/WK/W2/DS/DD/DJ/D2/DP/DX/RT/KA/KK/K1 Hands-Free Module (HFM) Error: "Could Not Find a Valid Writable USB Key"

Telemetics Gateway (TGW) Radio Flash (Reprogramming) Failure: “Negative Response 0x22 - 'Conditions Not Correct' Received from Start Routine by Identifier Request”

Radio Flash Process Failed: "No Response Received from Start Diagnostic Session Programming Request"

HVAC ECU Flash (Reprogramming) Failure: “No Response to Transfer Data Request” OR “NR 0x31 - 'Request Of Out Range' Received from Request Download Request”

2009-2010 DS, DJ, D2, DD, DP (Ram Trucks) Heating, Ventilation, & Air Conditioning (HVAC) ECU Will Not Flash Due to an ECU Issue

2010 RT Cabin Compartment Node (CCN) Flash (Reprogramming) Failure: “No response received from Start Diagnostic Session Extended request,” CCN Unresponsive After Flash Failure

2011 JK (Wrangler) Cabin Compartment Node (CCN) Flash Process Failed: No Response Received from Transfer Data Request

Blind Spot Module (BSM) Flash Process Failed: ECU Reports Unknown Precondition