2005/2006 ND (Dakota) Occupant Restraint Controller (ORC) Flash Process...
VEHICLE: 2005/2006 ND (Dakota) ECU: Occupant Restraint Controller (ORC) ERROR MESSAGE: Negative response 0x11 - 'Service Not Supported' received from Start Diagnostic...
View Article2010-2011 Cummins 6.7L ECM (Engine Control Module) Flash (Reprogramming)...
VEHICLE: 2010-2011 Ram 2500/3500/4500/5500 6.7L Cummins ECU: CM2200 Cummins ECM ERROR MESSAGE: Error received retrieving channel parameter - Unable to open...
View Article2007-2010 JK (Wrangler) KA (Nitro) Cabin Compartment Node (CCN) Flash...
VEHICLE: 2007-2010 JK Wrangler, all engines 2007-2010 KA Nitro, all engines ECU: Cabin Compartment Node (CCN) Cluster POTENTIAL ERROR ME SSAGES: No response received from...
View Article2004-2005 HB and 2005 LX Next Generation Controller (NGC) Powertrain Control...
VEHICLES: 2004-2005 HB Durango and 2005 LX 300/Magnum/Charger DESCRIPTION: If the flash fails or is aborted on the above vehicles this PCM will become unusable and replacement will be required. If the...
View Article2011 LX/LD (300C/Charger) JC (Journey) Body Control Module/Common Body...
VEHICLES: 2011 LX/LD (300C/Charger) 2011 JC (Jouney) DESCRIPTION: If the flash fails or is aborted at a particular point in the flash process on these vehicles, the BCM ECU MAY...
View Article2011 JC/JF/LD/LX (Journey/Charger/300) Hands-Free Module (HFM) ECU Flash Failure
VEHICLES: 2011 JC/JF/LD/LX DESCRIPTION: The Magneti Marelli HFM USB flash process failed and the ECU is no longer responsive; the ECU now shows up “red” in the vehicle view. If the HFM flash process is...
View ArticleNGC4 PCM (Powertrain Control Module) Flash Process Fails with "No Response...
VEHICLE: 2007+ vehicles with 2.7L, 3.5L 3.7L, 3.8L, 4.0L 4.7L, 5.7L, or 6.1L engines using NGC4 PCM ECU: NGC4 (Next Generation Controller) DESCRIPTION: Flash process fails with message, "No...
View Article2012-2013 JC/JF (Journey/Freemont) Antilock Brake System/Electronic Stability...
VEHICLES: 2012-2013 JC/JF (Journey/Freemont) ECU: ABS/ESP (Antilock Brake System/Electronic Stability Program) POSSIBLE ERROR MES SAGES: Negative response 0x7f - 'Service Not...
View ArticleUnable to Flash Reprogram Vehicle ECUs Using StarSCAN
ERROR MESSAGE: Unable to flash with StatSCAN: "Only the StarMOBILE or the wiTECH system can perform this action" DESCRIPTION: Due to the ongoing increase in vehicle and ECU technology, new flash files...
View Article2013 PF (Dart) PCM (Power Train Contol Module) Post Flash Reprogramming...
VEHICLE: 2013 - 2014 PF (Dart) 1.4L Turbo ECU: 8GMW PCM 8GMK PCM ISSUE: Certain procedures must be performed on an 8GMW and 8GMK PCM for PF 1.4L after flash...
View Article2014 KL (Cherokee) IPC (Instrument Panel Cluster) non-functional with codes...
Vehicle: 2014 KL (Cherokee) ECU: IPC (Instrument Panel Cluster) Potential Issue: IPC ECU (Electronic Control Module) part number may not update to the new expected part number and the IPC ECU is in a...
View Article2013-2014 WK/DS (Grand Cherokee and Ram 1500) Air Suspension Module (ASCM)...
2013-2014 WK (Grand Cherokee) 2013-2014 DS (Ram 1500) ASCM Air Suspension Control Module All general flash procedures in the service...
View ArticleFinding Aftermarket equipment on vehicles
DESCRIPTION ECU Flash Reprogramming and Diagnostic Routine failures have been known to be caused by aftermarket equipment installed on a vehicle. If an ECU flash reprogramming session or routine fails...
View Article2011 JC/JF/LD/LX (Journey/Charger/300) Hands-Free Module (HFM) Error Occurred...
VEHICLES: 2011 JC Journey 2011 JF Journey (Fiat) 2011 LD Charger 2011 LX 300 DESCRIPTION: A USB cable is required to flash the Magneti Marelli HFM ECU. If the cable is not connected when...
View Article"Boot Strap" Error Occurs When Using DRB III to Flash TCM on 2001-2004 JR
VEHICLES: 2001-2004 JR 2.7L 41TE automatic transmission SUGGESTIONS: Verify the DRB III is at the latest release using TechTOOLS. Verify the CH7000 red-ended cable is being used and is in good...
View ArticleSupplemental Reprogramming Tool (SRT 8432) Issue: Flash Download Failed
DESCRIPTION: Some 2001 to 2005 ST22 – Sebring/Stratus 3.0L PCM/ECM flashes require the use of the SRT 8432 device with the TechTOOLs application. When selecting the appropriate flash file to download...
View ArticlePowertrain Control Module (PCM) Flash Locks Up When Using the Supplemental...
VEHICLE: ST22 Sebring/Stratus Coupe 3.0L V6 SOHC RECOMMENDATION: If the PCM flash process is locking up, make sure that the SRT cabling is connected properly and the cables are not damaged. If...
View ArticleInstructional Guide: Flashing with StarSCAN or StarMOBILE
Please see the attached PDF document for a guide on how to flash using StarSCAN or StarMOBILE.
View ArticlewiTECH "New Flash Available" Icon Functionality
The purpose of this article is to explain the "New Flash Available" icon's functionality and how it relates to service documentation (Service Bulletins, Safety Recalls, and Rapid Response...
View ArticleChrysler Scan Tool Flash Availability Document
See the "Chrysler Scan Tool Flash Availability" PDF attached below.
View Article2011 JC (Journey) JF (Freemont) Cabin Compartment Node (CCN) Flash...
VEHICLE: 2011 JC (Journey) 2011 JF (Freemont) ECU: Cabin Compartment Node (CCN) Cluster POTENTIAL ERROR MESSAGES: "Could not open hardware channel - error...
View ArticleCCN Flash Process Failed: No Response Received from Start Diagnostic Session...
ECU: Cabin Compartment Node (CCN) DESCRIPTION: This flash failure has been known to be caused by a poor networking environment. Networking issues are very difficult to detect and can be...
View ArticleCCN ECU Flash Process Failed: No Response Received from Reset ECU Hard Request
ECU: Cabin Compartment Node (CCN) DESCRIPTION: This flash failure has been known to be caused by a poor networking environment. Networking issues are very difficult to detect and can be intermittent at...
View Article2005-2007 ND (Dakota) Occupant Restraint Controller (ORC) Flash Failure
VEHICLE: 2005-2007 ND (Dakota) DESCRIPTION: If the flash fails or is aborted on this vehicle, the ORC ECU will display as a unresponsive and replacement will be required. This is a known ORC ECU issue...
View Article2010 JS CCN (Cluster) Flash Process Failed: Negative response 0X33 –...
VEHICLE: 2010 JS (Avenger/Sebring) ECU: CCN (Cluster) ERROR MESSAGE: Negative response 0X33 – “Security Access Denied / Security Access Requested” received from Transfer Data...
View Article2007-2011 Cummins 6.7L ECM (Engine Control Module) Flash (Reprogramming)...
VEHICLE: 2007-2011 Ram 2500/3500 6.7L Cummins ECUs: CM2100 and CM2200 Cummins ECM ERROR MESSAGE: Flash Process Failed with "No Response received from Transfer Data request". DESCRIPTION: ...
View ArticleFlash Process Failed: Could Not Open Required Hardware Channel to Vehicle
DESCRIPTION: This particular flash failure has been known to be caused by a poor networking environment. Networking issues are very difficult to detect and can be intermittent at times. They can range...
View ArticleCCN Flash Process Failed: No Response Received from Transfer Data Request
ECU: Cabin Compartment Node (CCN) DESCRIPTION: This flash failure has been known to be caused by a poor networking environment. Networking issues are very difficult to detect and can be intermittent at...
View Article2007/2008 WK/XK (Grand Cherokee, Commander) Heating, Ventilation, & Air...
VEHICLE: 2007 and 2008 WK (Grand Cherokee) 2007 and 2008 XK (Commander) ERROR MESSAGE: No Response to Transfer Data Request DESCRIPTION: This particular flash failure...
View Article2007-2011 Cummins 6.7L ECM (Engine Control Module) Flash (Reprogramming)...
VEHICLE: 2007-2011 Ram 2500/3500 6.7L Cummins ECU: CM2100 and CM2200 Cummins ECM ERROR MESSAGE: Negative response 0x80 - 'Service Not Supported in Active Diagnostic Session' received from Transfer Data...
View Article2008-2010 ND (Dakota) Occupant Restraint Controller (ORC) Flash Process...
VEHICLE: 2008-2010 ND (Dakota) ECU: Occupant Restraint Controller (ORC) ERROR MESSAGE: Unlock of ECU failed DESCRIPTION: This ECU reprogramming...
View Article2010 JS (Avenger/Sebring) Heating, Ventilation, & Air Conditioning (HVAC) ECU...
VEHICLE: 2010 JS Avenger/Sebring POSSIBLE ERROR MESSAGES: Flash Process Failed - Invalid Response Could not open hardware channel DESCRIPTION: These particular ECU reprogramming...
View ArticleDiesel 2009 JC (Journey) & JS (Avenger/Sebring) Transmission Control Module...
VEHICLES: 2009 JC Journey 2.0L Diesel 2009 JS Sebring 2.0L Diesel ECU: TCM (Getrag) ERROR MESSAGE: Flash process failed - error received saving channel parameter - Unable to open channel! ...
View Article2009-2010 LX (300/Magnum/Charger) LC (Challenger) Totally Integrated Power...
VEHICLE: 2009-2010 LX (300/Magnum/Charger) LC (Challenger) ECU: Totally Integrated Power Module (TIPM) ERROR MESSAGE: Could not open required hardware channel to...
View Article2011-2012 WK/WD (Grand Cherokee/Durango) Antilock Brake System (ABS)...
VEHICLE: 2011-2012 WK (Grand Cherokee) 2011-2012 WD (Durango) ECU: ABS/ESP-ECU ERROR MESSAGE: Flash process failed - negative response 0x72 - 'General Programming Failure' received from...
View Article2009-2010 DS/DX Ram 1500 Cabin Compartment Node (CCN) Flash (Reprogramming)...
VEHICLES: 2009-2010 DS Ram 1500, all engines 2009-2010 DX (Mexico) Regular Cab Chassis, all engines ECU: Cabin Compartment Node (CCN) Cluster ERROR MESSAGE: No response received...
View Article2010-2011 Cummins 6.7L ECM (Engine Control Module) Flash (Reprogramming)...
VEHICLE: 2010-2011 Ram 2500/3500/4500/5500 6.7L Cummins ECU: CM2200 Cummins ECM ERROR: Device did not respond when sending Transfer Data request DESCRIPTION: ...
View Article2008–2012 PM/MK (Caliber/Compass/Patriot) Transmission Control Module (TCM)...
VEHICLE: 2008-2012 PM (Caliber) 2008-2012 MK (Compass/Patriot) ECU: Transmission Control Module (TCM) ERROR MESSAGE: Negative response 0x80 - 'Service Not Supported In Active...
View Article2014 WK AMP
VEHICLE: 2015 WK (Grand Cherokee) ECU: Amplifier (AMP) Control Module SUBJECT: This is a known AMP Electronic Control Module (ECU) issue and should not be mistaken for a wiTECH tool issue. It may occur...
View Article2014/2015 KL (Cherokee) RDM & PTU Flash process failed - negative response...
VEHICLES: 2014/2015 KL (Cherokee) ECU: RDM & PTU ERROR MESSAGE: Flash process failed - negative response 0x22 - 'Conditions Not Correct' received from Start Diagnostic Session Programming...
View Article2014/2015 KL (Cherokee) Electronic Steering Lock (ESL) “Flash process failed...
VEHICLES: 2014/2015 KL (Cherokee) ECU: ESL (Electronic Steering Lock) ERROR MESSAGE: Flash process failed – no response received from Start Diagnostic Session Programming request ...
View Article2015 JK (Wrangler) AMP (Amplifier Control Module) Non-Responsive
VEHICLE: 2015 JK (Wrangler) ECU: AMP (Amplifier Control Module) SUBJECT: The supplier of this AMP ECU (Electronic Control Unit) has identified an issue that may cause this AMP ECU to become...
View Article2014-2105 VF (Ram ProMaster) BCM (Body Control Module) Non-responsive
VEHICLE: 2014-2105 VF (Ram ProMaster) ECU: BCM (Body Control Module) DESCRIPTION: The supplier of this BCM ECU (Electronic Control Unit) has identified an issue that may cause this BCM ECU to become...
View ArticlewiTECH “New Flash Available” icon missing for 2015 BU/FB, version 16.01.18
wiTECH “New Flash Available” icon missing for 2015 BU/FB, version 16.01.18 VEHICLES: 2015 BU (Jeep Renegade) 2015 FB (Fiat 500x) Application: wiTECH (version 16.01.18) SUBJECT: The “Vehicle...
View ArticlewiTECH 16.01 – User Receives “Unable to flash controller due to communication...
SUMMARY You may receive this message: “Unable to flash controller due to communication error with the tool” during the ECU Flash process. The screenshot below depicts the error message: PROCEDURE...
View ArticlewiTECH Application 16.01 - User Is Unable to Perform ECU Flash on Legacy...
SUMMARY With wiTECH 16.01, if you attempt to perform an ECU flash on the PCM/TCM ECUs of some 2004–2006 MY vehicles, you will encounter issues. You may get stuck in the flash progress bar screen, which...
View Article2013-2014 PF 1.4L TCM DDCT (Dodge Dart): “Flash process failed - negative...
VEHICLES: 2013 PF 1.4L (Dodge Dart) 2014 PF 1.4L (Dodge Dart) ECUs: TCM DDCT (Transmission Control Module, Dual Dry Clutch Transmission) SUBJECT: “Flash process failed – negative response 0x83 –...
View Article2016 KL PCM 2.4L/3.2L (Jeep Cherokee) PCM (Powertrain Control Module) & TCM...
2016 KL PCM 2.4L/3.2L (Jeep Cherokee) PCM (Powertrain Control Module) & TCM (Transmission Control Module) Active DTC C10D0 VEHICLEs: 2016 KL 2.4L/3.2L (Jeep Cherokee) ECUs: PCM (Powertrain Control...
View ArticleEnhanced DRB III Emulator
Overview The DRB III™ hardware device is a handheld diagnostic tool that preceded the Next Generation Service Tool (NGST) family of service tools in FCA dealerships. This tool was introduced in 1994...
View Article2014-2017 WK/WD BSM may not be abort-recoverable
2014-2017 WK/WD Blind Spot Module (BSM) Flash Part Number Retrieval Failure after aborted/interrupted flash. DESCRIPTION: Part Number Retrieval may fail after an aborted/interrupted flash session. ...
View Article