2011 JK/KA/KK/RT/DS/DJ/WK/WD (Wrangler/Nitro/Liberty/Caravan/Town&Country/Ram...
2011 JK/KA/KK/RT/DS/DJ/WK/WD (Wrangler/Nitro/Liberty/Caravan/Town&Country/Ram Trucks/Grand Cherokee/Durango) TIPM (Totally Intergrated Power Module) flash process failed - no response received from...
View ArticlewiTECH ECU Flash Warranty Information - Warranty Bulletin D-09-12 and Labor...
All available service documentation (SB's, RRT's, Recalls) must still be reviewed to confirm that the flash is applicable to the vehicle BEFORE flashing to ensure that the available flash applies to...
View ArticleMagneti Marelli HFM USB Cables
Attention Non-U.S. and Non-Canadian Dealers: Beginning with the 2011 Dodge Journey (JC), Chrysler 300 (LX), and Dodge Charger (LD), all non-US and -Canadian dealers will be required to purchase the...
View ArticlePCM Has Been Replaced – What To Do Next?
After PCM replacement, there are some simple steps to follow using the wiTECH Diagnostic Application to properly connect to the vehicle: Open the wiTECH Diagnostic Application, select your device in...
View Article2011–2012 JC/JF/LD/LX (Journey, Freemont, Charger, 300C) Hand Free Module...
Vehicle: 2011 – 2012 JC/JF/LD/LX (Journey, Freemont, Charger, 300C) ECU: Hands Free Module (HFM) Potential Error Message: "Flash Process Failure - unexpected error occurred - Executable name...
View ArticleECU Flash Failure: What to do Next?
When the initial attempt to perform an ECU Flash fails, the following steps should resolve the issue: Read all available service documentation (SBs, RRTs, Recalls) from the wiTECH Diagnostic...
View ArticleFlash Reprogramming ECUs Using a Portable Laptop PC
DESCRIPTION: Laptops are usually set to a default Power Scheme that controls how long the computer must be idle/inactive before turning off the monitor, sleeping, standby, or shutting down. The default...
View Article2012/2014 WK/WD (Grand Cherokee/Durango) ABS/ESP Flash Process Failed – Erase...
VEHICLES: 2012/2014 WK (Grand Cherokee) 2012/2014 WD (Durango) ECU: ABS/ESP-ECU ERROR MESSAGE: Flash process failed – erase of logical block failed. ...
View Article2012 FF (Fiat 500) PCM (Power Train Module) Flash Reprogramming Failure: No...
VEHICLE: 2012 FF (Fiat 500) ECU: 8GMC PCM (Powertrain Control Module) FLASH FAILURE MESSAGE: No response received from Write Data By Identifier request SUBJECT: This...
View Article2012 FF (Fiat 500) P1302 Active or Stored DTC in PCM (Powertrain Control...
VEHICLE: 2012 FF (Fiat 500) ECU: 8GMC PCM Diagnostic Trouble Code (DTC) P1302 – Transmission Self Learning SUBJECT: After flash reprogramming an 8GMC PCM on the Fiat 500,...
View Article2012-2013 FF (Fiat 500 and Abarth) PCM (Power Train Contol Module) Post-Flash...
VEHICLE: 2012-2013 FF (Fiat 500 and Abarth) ECU: 8GMC PCM 8GMW PCM SUBJECT: Post-flash reprogramming procedures must be performed on 8GMC and 8GMW PCM for Fiat 500 and...
View Article2012 FF (Fiat 500) PCM (Power Train Control Module) Flash Reprogramming...
VEHICLE: 2012 FF (Fiat 500) ECU: 8GMC PCM (Power train Control Module) ERROR MESSAGE: Negative response "0x22 - 'Conditions Not Correct'" received from "Start Diagnostic Session...
View Article2012-2013 FF (Fiat 500) PCM (Powertrain Control Module) Negative Response...
VEHICLES: 2012-2013 FF (Fiat 500) ECU: 8GMC PCM (Powertrain Control Module) ERROR MESSAGE: Negative response "0x22 - 'Conditions Not Correct'" received from "Start Diagnostic Session...
View ArticleGPEC PCM Flash (Reprogramming) Failure: “No Response Received from Start...
ISSUE: Flashing a GPEC PCM may result in an error message of “No response received from Start Diagnostic Session Extended request.” Flashing a GPEC PCM is very robust and has a very low flash failure...
View ArticleNGC4 PCM (Powertrain Control Module) ECU Flash Failed: ECU Is Not Responding...
VEHICLES: 2007+ Vehicles using NGC4 PCM ECU: NGC4 (Next Generation Controller) ERROR MESSAGE: ECU Flash Failed - The ECU is not responding to the tool as...
View ArticleNGC PCM Flash (Reprogramming) Failure: “NR 0x22 - 'Conditions Not Correct or...
ISSUE: Flashing a NGC PCM may result in an error message of “NR 0x22 - 'Conditions Not Correct or Request Sequence Error' received.” Flashing a NGC PCM is very robust and has a very low flash failure...
View Article2008-2010 R2 (CKD) Caravan/Voyager Next Generation Controller (NGC)...
VEHICLES: 2008-2010 R2 (CKD) Caravan/Voyager ISSUE: If the ECU reprogramming attempt fails or is aborted on the above vehicles, this PCM may become unresponsive and replacement may be required. The PCM...
View ArticleNext Generation Controller (NGC) Powertrain Control Module (PCM) Flash...
VEHICLES: 2007+ vehicles equipped with Next Generation Controller (NGC) ECU: NGC ISSUE: Flashing a NGC PCM results in an error message of “negative response 0x12 - 'Sub Function Not Supported / Invalid...
View ArticleGlobal Powertrain Engine Controller (GPEC) Powetrain Control Module (PCM)...
VEHICLES: 2007+ vehicles equipped with Global Powertrain Engine Controller (GPEC) ECU: GPEC ISSUE: Flashing a GPEC PCM may result in an error message of “negative response 0x12 - 'Sub...
View ArticleGlobal Powertrain Engine Controller (GPEC) Powetrain Control Module (PCM)...
VEHICLES: All vehicles equipped with GPEC PCM ECU: GPEC (Global Powertrain Engine Controller) ISSUE: Flashing a GPEC PCM may result in the error message: “NR 0x22 - 'Conditions Not...
View Article